The screen: Steps: Before test, set the DIP switch, jumper setup to software prompted Address Pin Test: click the one of the push button in the Address Out group, use multimeter detect output signal in the ZIF32 socket.Universal Willem EPROM Programmer PCB50X SPI FLASH BIOS ECU PICFree shipping: 28 VA06 Universal Willem EPROM Programmer PCB50X BIOS FLASH Burner PLCC BIOS freshing upgrading Upgrading, Programming BIOS chips.
Willem Pcb 5.0E Software Code Read WriteCar automotive ECU chip tuning, memory device code read write program.
ATMEL AVR Micros. V6 SPI device on your motherboard or HDD. Programming EPROM, EEPROM, FLASH Burner (Vpp 12.5V,21V,25V) Support CHIPS (EPROM, EEPROM, FLASH, I2C,PIC, MCS-51,AVR, 93Cxx, ISP) Build-in PLCC32 FLASH and PLCC32 Firmware HUBLPC socket on board. Fast programming time It is more STABLE than PCB3B (Standard) and Enhanced Willem It can program up to 30 FASTER more than v. PCB3B and Enhanced Willem It can select use the power supply from a USB port or DC Adapter by setting jumper It can set changes to be PCB3B or PCB4C by using jumper setting (when wish use Software of the ordinary 1 Qty Willem EPROM Programmer PCB50X 1 Qty Parallel Printer Cable 1 Qty Manual and Software in CD. Handling cost by Standard to Worldwide: FREE Shipping ( with Tracking ) time is approximately 15-20 Work days. France, Italy, Finland and Russian, The products maybe delay arrive to you more than 4 weeks because delivery system inside of those country. Willem Pcb 5.0E Software Update Support SPlAccepted PayPal or Another Payment Plaese contact with me The latest Software Version 0.98D12C3 for PCB50, PCB50a, PCB50B and PCB50X this increases the ability to support chips and also includes a function to search for chip number, SPl FLASH 25Cxxx (Auto Select) Software Version 0.98D12 for PCB50 and PCB50a update support SPl FLASH Software Version 0.98D11 - for PCB5.0 is now released. Software Version 0.98D10 - for PCB5.0 is now released. Software Version 0.98d9 - for PCB5.0, in stable beta now - adds support for 3V6 SPI Flash devices and includes many improvements. Software Version 0.98a (0.98a alpha) for PCB3B UP Software Version (0.98ap) CAN UNLOCK AM29F040B Software Version 0.97j, 0.97i, 0.98i, 0.97i, 0.97h, 0.97g. For Windows Operational System and support Willem EPROM Programmer PCB3b Software Hardware Features: combines the merits of dual powered (USBAC) willem version Enhanced willem version. Check there are any active resident programs that use the printer port, such as TWAIN drivers. Connect one end of the 25 pin SubD parallel cable to PC printer port Connect the other end of parallel cable to 25 Pins port of the programmer Connect USB power cable or AC adaptor (Note: if you are working on the EPROM programming. Select devices type Set the DIP switch based on the displayed pattern. Note: the LPT port of PC MUST set to ECP or ECPEPP during BIOS setup. Willem Pcb 5.0E Software Download From DownloadTo enter the BIOS setting mode, you need press Del key or F1 key during the computer selftest, which is the moment of computer just power up.) Software Version To Use The software can be download from download.mcumall.com There are board hardware selection jumper on the board. When set the jumper to PCB3B, then user have to use 0.97ja and before version software. If the board selection set to PCB3.5, PCB5.0, PCB5.5C, then the software 0.98D6 should be used. The software interface: Hardware Check After start the program, click test hardwar under Help menu. If the connection and power supply is normal, then appears: Hardware present Otherwise check if the programmer connects well with PC, or power supply is normal. PCB3.5PCB4E (Two PLCC32 adapter is not applied on the PCB4E) PCB5.0 PCB5.5C Note: the Vcc setting jumper only has effect when you are using AC adaptor as power source. Then set it again for ON or OFF. DIP Bit shift button to shift the DIP bit position to where need to set. And then press DIP Set button twice to check current DIP bit position. Repeat those steps till all DIP bit ae set same as software indicated. For PCB5.5C voltage and Special chip selection: 1. Put back the safety jumper. Press the voltage button and hold for 1 second, the voltage LED should move to next. Repeat till desired voltage LED light up. Press the chip selection button and hold for 1 second, the chip LED should move to next. Repeat till desired LED light up. Remove the safety jumper to lock the selected voltage and chip selection DIP Switch (PCB3.5, PCB5.0) When programming one chip, follow the program prompt to set DIP switch.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |